IB COMPUTER SCIENCE | A2.3.2 Transmission Media

Lesson objective

Compare fibre optic, twisted pair and wireless transmission using bandwidth, installation complexity, cost, range, interference, attenuation, reliability and security.

Learn

A2.3.2 | TYPES OF MEDIA FOR DATA TRANSMISSION

01 | THE DATA NEEDS A PHYSICAL JOURNEY

A laptop in a classroom, a switch in another building and a moving robot all need to send data, but their connections have different requirements. Running a cable to a stationary desktop can be sensible; attaching the same cable to a student walking between rooms is much less useful.

A transmission medium is the physical path or environment carrying a signal. This lesson compares twisted pair copper cable, fibre optic cable and wireless transmission. Copper carries electrical signals, fibre carries light, and the wireless examples here use radio waves.

Choosing a medium involves more than asking which has the largest advertised number. You must consider bandwidth, installation complexity, cost, range, interference, attenuation, reliability and security. The best answer connects these factors to the actual task.

A real network often combines the three: wireless access for mobile devices, twisted pair for local wired devices and access-point connections, and fibre between buildings or network tiers.

02 | BANDWIDTH, THROUGHPUT AND LATENCY

In this networking comparison, bandwidth usually means a link’s data-carrying capacity, commonly stated in bits per second. Throughput is the useful data rate actually achieved. Protocol overhead, other users, equipment limits and signal conditions can make throughput lower than a nominal link rate.

Latency is delay. It includes more than propagation through the medium: processing, queueing, contention and retransmissions can contribute. A high-capacity link does not guarantee that every response arrives with very little delay.

For example, a fast wireless connection can still deliver a slow download when many clients compete for airtime or the internet uplink is busy. Equally, replacing a desktop cable with fibre will not speed up a slow remote application if the bottleneck is elsewhere.

In physics, bandwidth can also refer to a frequency range in hertz. Keep the context clear: compare data capacity and useful throughput here, without treating frequency bandwidth and achieved bit rate as identical quantities.

03 | TWISTED PAIR: ELECTRICAL SIGNALS ON COPPER

Twisted pair cable contains insulated copper conductors arranged in pairs. The two wires in a pair twist along the cable. Suitable signalling and receiver design use the pair together, while the twisting helps reduce unwanted electromagnetic effects.

Common Ethernet cabling uses four pairs inside one jacket. Cable categories such as Cat 5e, Cat 6 and Cat 6A specify performance requirements; the supported link also depends on the Ethernet standard, length, connectors and equipment. “Copper” is not one fixed speed.

Twisting helps reduce crosstalk, which is unwanted coupling between nearby signal paths, and helps reject some external noise with balanced signalling. Shielded cable can offer further protection when installed and bonded appropriately. Neither approach means the link is immune to every disturbance.

Copper Ethernet is common for classroom desktops, printers, access points and other nearby devices because interfaces and installation skills are widely available. Some compatible links can also deliver electrical power using Power over Ethernet.

04 | WHY THE TWISTS MATTER

Imagine two nearby pairs carrying changing electrical signals. Energy from one can couple into the other and interfere with its receiver. Twisting and the cable’s balanced construction help limit or reject these unwanted effects.

Good cable can still perform poorly if a connector is badly terminated or the pairs are untwisted too far at the end. The installation is part of the communication system, not just the cable in the middle.

The illustration is a schematic of one pair, not a wiring instruction or a claim that bits always have the simple wave shapes shown.

ONE PAIR | TWO INSULATED CONDUCTORSTwisting helps control interference; it does not eliminate all noise.
The two colours distinguish the conductors. The drawing is symbolic.

05 | TWISTED PAIR: PRACTICAL LIMITS AND ADVANTAGES

For many ordinary four-pair office Ethernet standards, the complete copper channel is designed for up to 100 m, including patch leads. This is a useful typical comparison, not a universal limit for every copper technology or every transceiver. Always match the specific standard and equipment.

A short wired desktop link can provide stable, predictable service without competing for shared radio airtime. Existing cable routes, inexpensive interfaces and familiar termination methods often make it economical within one room or building.

The disadvantages include installing a physical route to each endpoint, cable-length limits, electrical interference risks and copper’s conductivity. Poor terminations, damaged cables or unsuitable cable types can cause errors even when the distance looks acceptable.

Power over Ethernet (PoE) can carry power and data to compatible equipment such as an access point. That is a useful extra capability, not a feature of every copper connection, and it requires compatible supplying and receiving equipment.

06 | FIBRE OPTIC: LIGHT THROUGH A GUIDED PATH

Fibre optic cable carries encoded data using light through a glass or plastic optical path. A transmitter converts information into an optical signal and a receiver detects it. The light-guiding core and surrounding cladding are part of the fibre’s construction.

Single-mode fibre guides light in one principal mode and is widely used for long-distance, high-capacity links. Multimode fibre supports multiple light paths and is common for suitable shorter building or data-centre links. Actual reach depends on fibre type and optical equipment, not just these two names.

The optical transmission path is immune to electromagnetic interference that can disturb electrical copper signalling. This is valuable near electrically noisy equipment and for links where electrical isolation is important. Equipment at either end still needs suitable power and protection.

Fibre is often chosen for backbones and building-to-building connections because appropriate fibre and transceivers can support high data rates over distances beyond ordinary office copper Ethernet channels. It is not automatically the fastest option for every possible short link.

07 | FIBRE: INSTALLATION AND COST NEED PLANNING

An optical link needs compatible transmitters, receivers, connectors and fibre. Single-mode and multimode components cannot simply be mixed without checking compatibility. Connector cleanliness, splice quality and the permitted bend radius affect the light reaching the receiver.

Fibre installation and testing can require specialist skills and tools, especially for field termination or splicing. Pre-terminated cables can simplify some work, but pulling routes, protecting connectors and testing the completed link still matter.

A fibre link can cost more initially because of optics, installation and testing, although actual total cost depends on the existing routes, length and scale. It can be good value when distance, capacity or electrical isolation makes copper unsuitable.

The optical fibre itself does not supply electrical power to the remote device. A powered camera or access point still needs an appropriate power arrangement. Hybrid products can include separate power conductors, but that is not electrical power travelling through the optical glass.

08 | WIRELESS: RADIO LINKS WITHOUT A CABLE TO EACH CLIENT

Wireless transmission uses electromagnetic waves through the environment rather than a dedicated cable to every endpoint. In the local networking examples here, Wi-Fi clients communicate with an access point using radio. Other wireless systems have different range and performance characteristics.

Mobility is a major benefit. A student can move with a laptop, and devices can connect where installing a cable is impractical. Adding a client does not require running a new desk cable, although sufficient coverage and capacity must already be available.

Wireless still needs infrastructure. Access points need power and often a wired backhaul connection to the rest of the network. Deployment requires channel planning, coverage testing, security configuration and enough capacity for simultaneous users.

Walls, distance, competing transmissions, antenna placement and the chosen frequency band affect performance. A strong displayed signal is useful evidence, but it does not by itself prove that the channel, access point and upstream network have spare capacity.

09 | SHARED AIRTIME IS A RESOURCE

Wi-Fi clients using the same channel contend for airtime. They do not each receive a private copy of the access point’s advertised capacity. Protocol overhead, contention and retransmissions reduce the useful data carried.

Consider four clients downloading at once through one constrained radio resource. A simple equal-share calculation can illustrate why demand matters, but real scheduling is not always equal and slower transmissions may occupy more airtime for the same amount of data.

More access points help only when channel use, placement, power and backhaul are planned. Placing many on the same crowded channel can add contention instead of creating unlimited capacity. Wireless mesh backhaul can also consume radio resources.

This is why a fixed classroom desktop may benefit from a wired connection while wireless remains the right choice for mobile tablets. The decision balances mobility and installation flexibility against the capacity and predictability needed.

10 | ATTENUATION: THE SIGNAL BECOMES WEAKER

Attenuation is reduction in signal strength or power as it travels through a path. It is different from latency: a weaker signal is not simply a signal that takes longer to arrive.

Copper has transmission losses that depend on factors including length, frequency, cable and connectors. Fibre has optical losses along its length and at connectors, splices and bends. Wireless signals spread out and can be absorbed or obstructed by materials in their path.

A receiver needs a sufficiently usable signal relative to noise and its design limits. If the received signal is inadequate, errors, lower usable rates, retries or loss of connection can result. Appropriate equipment and distance limits are therefore part of the design.

Fibre often supports low-loss long links with suitable optics, but “fibre has no attenuation” is wrong. Likewise, wireless range cannot be given as one distance that applies to every building and technology.

11 | INTERFERENCE: AN UNWANTED CONTRIBUTION TO THE SIGNAL

Interference is unwanted energy or competing transmission affecting reception. In copper systems, external electrical noise and crosstalk can be concerns. Proper twisted construction, separation and suitable shielding help manage them.

Optical signals in fibre are not affected by external electromagnetic interference in the way electrical copper signals are. They can still suffer optical loss, dirty connectors or damaged cable. Immunity to one type of disturbance is not immunity to every fault.

In wireless, nearby users and other emitters can compete with or disturb the intended link. Walls and distance mainly concern propagation and attenuation, while overlapping transmissions introduce other reception and contention problems. Real sites can have several effects together.

Compare the mechanism: “Fibre is suitable near noisy machinery because its light transmission is not disrupted by the electromagnetic noise that can affect copper signalling.” That is stronger than simply writing “fibre is more reliable”.

12 | INVESTIGATE A LINK CONDITION

Choose a situation to see how each medium responds. The activity gives qualitative design guidance, not measured signal levels or a guarantee of a particular speed. Specific cable categories, optics and radio technologies must be checked before deployment.

These are conditional comparisons. Link standards, survey results, installation routes and security requirements still need validation.

13 | RELIABILITY: ASK WHAT CAN GO WRONG

A well-installed wired link avoids competition for radio airtime and is often predictable for a fixed endpoint. It can still fail through a cable cut, a loose connector, damaged hardware, poor termination or loss of power at the equipment.

Fibre avoids electrical interference on the optical path, but poor connector hygiene, excessive bending or incompatible optics can make it unreliable. Copper can be reliable within its supported environment and length when properly installed and tested.

Wireless reliability depends on coverage, interference, load, roaming and equipment. It can be very useful and dependable when appropriately engineered; it is not inherently unsuitable for all important tasks. The requirements and consequences of interruption determine the design effort.

All three can share upstream dependencies. A perfect access cable does not help if the only switch or internet link fails. Redundant routes and equipment improve resilience to specified faults, but their design is a separate decision from choosing the medium.

14 | SECURITY: THE MEDIUM DOES NOT COMPLETE THE DEFENCE

Wired access normally requires access to cable infrastructure, a port or equipment. This can make casual interception harder than receiving radio transmissions, but exposed sockets, compromised devices or cable access can still provide attack opportunities.

Fibre is generally harder to tap casually and does not radiate the electrical signals of copper, but optical interception is possible. It is not automatically encrypted or impossible to intercept. Protect routes, equipment and administration, and use appropriate encryption for sensitive data.

Wireless signals can extend beyond a room or building, so an attacker may attempt reception or connection without using a physical socket. Strong supported authentication, encryption, access policy and maintained equipment are essential. Radio encryption does not replace application security.

For a fair comparison, say that the exposure and required controls differ. Do not claim that “wired is secure” or “wireless can never be secure”. Sensitive traffic can need end-to-end protection over any of the three.

15 | COMPARE ALL EIGHT REQUIRED FACTORS

FactorTwisted pair copperFibre opticWireless, such as Wi-Fi
Bandwidth / capacityCan support high local link rates with appropriate category, standard and lengthSuitable fibre/optics support very high-capacity linksDepends on radio standard, conditions, channel sharing and clients
Installation complexityCable routes, terminations and testing requiredOptics, connector care and sometimes specialist splicing/testingNo cable to each client; coverage, channels, power and backhaul need planning
CostOften economical for nearby fixed devicesOptics and installation can add cost; long-link value may justify itCan reduce client cabling but needs access points, backhaul and support
RangeMany ordinary office Ethernet channels support up to 100 m; check the exact linkAppropriate fibre and optics can cover much longer distancesVaries strongly with technology, band, obstacles and environment
InterferenceElectrical noise/crosstalk require managementOptical path immune to electromagnetic interferenceCompeting transmissions and emitters can affect reception
AttenuationElectrical loss grows with path and frequency-dependent factorsOptical loss exists along fibre and at joins/bendsPath loss and material obstruction weaken signals
ReliabilityPredictable when correctly installed within limitsReliable suitable links; damage or dirty optics can still failRequires sufficient coverage and capacity under changing conditions
SecurityProtect ports and routes; use suitable encryption/access controlsHarder casual tapping does not mean encryption or invulnerabilityRadio exposure makes authentication/encryption and policy especially important

Read this as a conditional comparison rather than a ranking from best to worst. A medium can score well on one requirement while being unsuitable for another.

16 | APPLY THE COMPARISON TO A CAMPUS

A campus needs three different connections. Fixed desktops are 25 m from a switch, buildings are separated by 250 m, and students carry tablets between rooms. A single medium for every path would ignore those differences.

Suitable twisted pair is a plausible economical choice for the nearby desktops. Fibre with matched optics is a strong candidate for the inter-building backbone because of distance, capacity and electrical isolation. Wireless access supports tablet mobility, with planned access points and sufficient backhaul.

This is a proposed design, not a specification to install without a survey. Building routes, power, local regulations, existing equipment, expected traffic and future growth influence the actual implementation.

In an exam answer, connect your choice to the stated requirement and compare an alternative: “For the 250 m backbone I would favour suitable fibre over ordinary office copper Ethernet, because the distance exceeds many standard 100 m copper channel limits, while fibre optics can be selected for the required reach.”

17 | CHOOSE A JUSTIFIED STATEMENT

Each situation has one best-supported statement. Choose the answer that links the medium’s characteristics to the requirement without making an absolute claim.

18 | WRITE A COMPARISON WITH A REASON

For compare, identify relevant similarities and differences. Use the same factor for both media, then explain its importance in the given situation. A list saying “cheap, fast, secure” without conditions leaves the comparison unclear.

For example: “Both copper and fibre require installed cable routes. Twisted pair is often economical for nearby fixed endpoints, whereas fibre may require more specialised optical components and handling. However, suitable fibre supports the longer inter-building path and avoids electrical interference on its optical signal, making the extra installation work worthwhile here.”

For mobile use: “Wireless avoids a cable to each moving client, whereas either wired medium constrains movement. However, clients share radio resources and coverage varies with the environment, so access-point planning and security configuration are needed.”

Use both, whereas, because and therefore. Distinguish bandwidth from achieved throughput, attenuation from delay, and the medium’s properties from the security and reliability of the complete system.

MATCH THE MEDIA IDEA TO ITS MEANING

Terminology

Terminology

Transmission medium

The physical path or environment carrying a communication signal.

Twisted pair

Insulated copper conductors arranged in pairs that twist along the cable.

Fibre optic

A medium carrying encoded information using light through an optical path.

Wireless transmission

Transmission through the environment without a dedicated signal cable to each endpoint.

Electrical signal

Information represented by changing electrical quantities on a conductive path.

Optical signal

Information represented using light.

Radio wave

An electromagnetic wave used by the wireless examples in this lesson.

Bandwidth

In this comparison, the data-carrying capacity of a link, usually stated in bits per second.

Throughput

The useful data rate actually achieved.

Latency

Delay in communication, including relevant propagation, processing and waiting.

Attenuation

Reduction of signal strength or power along a path.

Interference

Unwanted energy or competing transmission affecting reception.

Crosstalk

Unwanted coupling from one signal path into another.

Shielding

Protective conductive construction that can reduce certain interference when correctly installed.

Cable category

A cabling performance classification, such as Cat 6 or Cat 6A.

Termination

Connecting the cable conductors or optical path to the appropriate interface or connector.

Single-mode fibre

Fibre guiding one principal optical mode, commonly used for long-reach suitable links.

Multimode fibre

Fibre supporting multiple optical paths, common for suitable shorter optical links.

Transceiver

Equipment that transmits and receives signals on a compatible link.

Optical splice

A join between optical fibres that contributes to the link’s loss and installation requirements.

Bend radius

A limit on cable curvature needed to avoid damage or excessive loss.

PoE

Power over Ethernet: electrical power delivery over compatible copper Ethernet links.

Access point

A device providing wireless network access for clients.

Backhaul

The connection carrying access traffic toward the rest of the network.

Airtime

Time using the shared radio transmission resource.

Contention

Competition among participants for a shared communication resource.

Coverage

The area in which a wireless service meets the required reception and operation conditions.

Electrical isolation

Separation that avoids an electrical conductive signal path between endpoints.

Encryption

Cryptographic protection of content, not automatically supplied by choosing a cable medium.

Total cost

Purchase, installation, operation and maintenance expenses considered together.

Questions

Questions

CHECK YOUR UNDERSTANDING

Select all correct choices. Each exact set earns one point.

1. Which correctly match signals and media?
2. Which are accurate capacity statements?
3. Which describe twisted pair?
4. Which describe fibre?
5. Which describe wireless deployment?
6. Which distinguish attenuation and interference?
7. Which are fair range comparisons?
8. Which security statements are accurate?
9. Which suit the illustrative campus requirements?
10. Which improve an exam comparison?

EXPLAIN AND COMPARE

Write your answers before revealing each sample.

1. Compare how the three media carry signals.

2. Compare bandwidth and throughput.

3. Explain why twisted pair can suit fixed classroom desktops.

4. Compare interference susceptibility of copper and fibre.

5. Compare fibre and ordinary office copper for a 250 m building link.

6. Explain attenuation in all three media.

7. Compare wireless and wired access for moving tablets.

8. Explain why adding more access points does not guarantee more throughput.

9. Compare security exposure across the media.

10. Compare installation complexity and total cost.

11. Explain why fibre does not guarantee complete system reliability.

12. Suggest and justify a mixed campus design.

COMPARE IT | THREE CAMPUS LINKS

A campus needs fixed desktops within 25 m of a switch, a 250 m building-to-building link and access for moving tablets. Propose a medium for each. Compare suitable alternatives using all eight factors from this lesson and justify the relevant trade-offs. Identify one capacity bottleneck and one security requirement that your choice of medium does not automatically solve.

Flashcards

Flashcards

Click to flip. Select the ideas you need to revisit.

0 cards selected for revision.

    Selections are kept while this page is open.

    Workbook

    Workbook

    COMING SOON

    The workbook for A2.3.2 Transmission Media is coming soon. Complete the matching task and written questions in your exercise book.